When aandhi or windstorm hits Delhi-NCR or north India, most of us bring the clothes in and close the windows. If you have solar panels on the terrace, there’s a bigger question. Can strong winds loosen a panel and send it into the lane or onto a neighbour’s roof?
Yes, it can happen if the parts holding the panel or the frame in place break or come loose. So before you finalise a rooftop solar vendor, ask your installer to show you what holds the panels in place, what keeps the steel frame steady and how that frame is fixed to your roof.
MYSUN rooftop installation in Delhi.
Start by looking underneath the panels
From the street, most solar installations look much the same. From the terrace, you can see the parts that hold the panels in place. In the photo above, look for the diagonal steel braces, the bolts where the steel pieces meet, and the round concrete bases at the bottom of the columns. Each has a different job when the wind picks up.
Can solar panels fall off in a Delhi NCR storm?
Yes. A panel can lift off if its clamp breaks or comes loose even if the steel frame is still standing. If a brace, connection or roof fixing gives way, a group of panels can shift or collapse with the panels still attached. That is why we look at the panel fasteners, the steelwork and the attachment to the roof together.
How common is it in Delhi NCR?
Delhi-NCR does get strong winds during storms. During the thunderstorm on 24–25 May 2025, the India Meteorological Department recorded wind speeds of up to 82 km/h at Safdarjung. Public reporting documents storms like this, but there is little reliable local data on how often rooftop solar panels come loose across Delhi-NCR. PTI report on the May 2025 storm
What could it cost you?
A clamp or one panel may be all that needs replacing. A bigger failure can damage several panels, bend the steel frame, pull on cables or damage the terrace and its waterproofing. A badly damaged system may need a partial or full rebuild, with your solar system switched off while it is made safe and repaired. That can put a substantial part of your investment at risk.
There’s also the risk to people and property below. A falling panel or piece of steel could injure someone on a terrace, in a courtyard or in the lane. It could also damage a parked car, a water tank or a neighbour’s roof. On a narrow lane with homes close together, the consequences can reach beyond your own terrace.
What does the wind speed on my quote mean?
Think of a patio umbrella on a windy day. Strong wind can push it sideways or lift it. Wind can do the same to solar panels, pushing against them or lifting them from below. On a raised structure, there is room for air to move beneath the panels, so we have to consider how the wind pushes and lifts the panels and frame.
Why two houses on the same street can need different designs
Picture a low-rise house tucked between other buildings and a taller corner home with open ground on one side. One owner wants their panels low over the roof. The other wants enough headroom to walk underneath. Even on the same street, the roof height, how open the area is, and where the panels sit can change what the frame and its fixings need to handle. Think of a crowded terrace in East Delhi or Ghaziabad, a builder floor in Gurugram, or an independent home on a more open plot outside Meerut, Sonipat or Faridabad. The same layout may make little sense on all three.
When we look at a roof, the questions are practical. How high is the roof above ground? How high will the panels sit above the terrace? Are the panels close to the edge of the roof? Which way will it tilt? And what will the structure be fixed to? Your installer should be able to explain how the proposed design accounts for those conditions.
What does designed for up to 170 km/h mean?
MYSUN designs rooftop solar structures for wind speeds of up to 170 km/h, depending on the roof and the layout. Ask us what wind speed we used for your home and how we chose it.
Even a small rise in wind speed can put much more pressure on the panels and frame. For example, going from 150 to 170 km/h means about 28% more wind pressure under the same conditions. The height of the frame, the angle of the panels and the way the frame is fixed to the roof all matter.
The Indian code of practice for wind loads is IS 875 Part 3. Ask your installer for the design wind speed they used for your rooftop and the assumptions behind it. Bureau of Indian Standards
How MYSUN designs for strong winds
We start with the roof and the layout. A terrace with water tanks, the room at the top of the stairs and limited walking space needs a layout that fits the home. A raised frame that clears those obstacles still has to handle the wind at that height. We look at how the panels, steel frame and roof fixings will work together in the proposed layout.
Front three-quarter illustration showing the braced frame and column bases. Opposite-side illustration showing the frame from the other direction.
Why those diagonal pieces matter
Imagine pushing sideways on a rectangular frame. It can lean out of shape. Add a diagonal and you form a triangle, which helps the frame hold its shape. In the pictures above, those slanted steel pieces brace the frame against sideways movement. Their connections at either end are part of what makes them work.
The panel fasteners and the roof fixings do different jobs
At the top, the panel fasteners hold the panels to the supporting steel. The steel bars beneath the panels pass that force to the upright columns. At the bottom, the anchors hold the frame to the roof and pass those forces into it. Ask us to show you where each of those connections sits on your proposed installation.
Will the steel rust after a few monsoons?
The steel under your panels spends every day outside. It sees rain, humidity, dust and repeated wetting and drying. At MYSUN, we use hot-dip galvanised steel for the columns and Galvalume-coated steel or HDGI Steel for the rafters and purlins. Here’s what that means when you’re looking at a quote.
Hot-dip galvanised columns
Hot-dip galvanising means dipping the steel into molten zinc. The zinc reacts with the steel and forms a bonded coating. That coating helps keep moisture and oxygen away from the steel. Zinc also wears away before the steel does. This can help protect the steel around a small scratch.
What a micron tells you
MYSUN specifies an 80-micron zinc coating on its hot-dip galvanised columns. That’s 0.08 mm. This layer helps protect the steel from rust as the columns face years of rain and damp weather. The condition of the coating and how much moisture it is exposed to also affect how long it lasts.
The finish can look shiny, dull or mottled. To compare two quotes, look at the written coating specification and ask how the supplier checks it. American Galvanizers Association
Galvalume rafters and purlins
Rafters are the main sloping members beneath the panels. Purlins run across them to support the panels. MYSUN uses Galvalume-coated steel for both. Galvalume uses an aluminium-zinc alloy coating to help protect the steel. You may see Galvalume coating listed in grams per square metre. That tells you the weight of the coating over a given area. Microns tell you how thick a coating is.
Why we bolt the frame together on your roof
Our team assembles the frame on the roof with bolted connections, using SS304 stainless steel fasteners as specified. Welding on the terrace would introduce heat that can damage the protective coating locally. Bolted assembly avoids that on-site welding step. The bolts you see in the close-ups join specific pieces of the frame so they can work together.
Extra Strength - A closer look at the steelwork
The diagonal brace connects to a cross member and helps the frame resist sideways movement. Purlins and rafters support the panel assembly and carry forces to the columns.
How the structure meets your roof
Those round concrete bases are easy to spot in the photo. What’s harder to see is how the structure is secured below the visible surface. When the wind pulls up or pushes sideways, the fixings have to carry those forces into the roof. During the survey, we assess where the columns can sit and how the frame can be supported and fixed.
If your terrace has a reinforced concrete slab and the design calls for drilling, we use chemical sealing at the fixing points to help keep rainwater out. The anchor holds the structure in place, and the sealing helps protect against water getting in around the fixing. If you already have a waterproofing layer or have had seepage before, tell the team during the survey so they can look at those areas when discussing the layout.
The steel column meets the concrete base at roof level and is sealed with Chemical Bonding.
A bolted beam-to-column connection near the upper edge of the frame.
MYSUN rooftop solar installations
See how raised panels fit different homes and terraces, from roofs where you need room to walk to terraces you use as a garden.
Raised solar panels with diagonal steel supports and concrete bases.
Two raised groups of panels above a home with a spiral staircase.
How raised panels fit different terraces
Solar panels above a planted terrace.
A view from beneath the raised panels showing the steel frame and space on the terrace.
Questions homeowners ask about rooftop solar
Q1: Can my panels fall off during aandhi/ windstorm?
Yes. If a clamp breaks or comes loose, a panel can lift off. If the frame or the bolts holding it to the roof fail, several panels can move together. A falling panel can injure someone or damage a car, a water tank or a neighbour’s home.
Q2: Is this common in Delhi NCR?
Delhi-NCR gets strong winds during storms. There is little reliable local data on how often solar panels come off roofs. Ask your installer how they will secure the panels and frame on your home.
Q3: What wind speed does MYSUN design for?
We design structures for wind speeds of up to 170 km/h, depending on the roof and layout. Ask for the figure for your home, especially if you want a tall frame or your roof is in an open area.
Q4: What does 80-micron zinc coating mean for my roof?
It is the thickness of the zinc layer we specify on the upright steel columns. The zinc helps protect them from rust. MYSUN uses a separate aluminium-zinc coating called Galvalume on the steel supports under the panels.
Q5: Will there be welding on my terrace?
We bolt the frame together on-site, using SS304 stainless steel fasteners as specified. This avoids on-site welding and the heat that can damage the coating around a weld.
Q6: What about water leaking where you drill?
Where the design calls for drilling into a reinforced concrete roof, we use chemical sealing around the fixing points to help keep water out. Tell us during the survey if the terrace already has seepage or a waterproofing layer.
Q7: What if something looks loose after a storm?
Keep people away from that part of the terrace and the area below it. Call your installer to check the panels, frame and roof fixings.
Plan your rooftop solar with MYSUN
When we visit your home, ask us to show you where the panels would sit, how high the frame would be and how we would fix it to your roof.
With 4000+ Solar Projects and 10+ year’s experience of Solarizing Homes, MYSUN is NCR’s leading Solar Company and the 1st prize winner by TPDDL.
Book a rooftop survey with MYSUN. Call 9873167009 or 8448380218 , or visit itsmysun.com .
Comments